Sevgili ustalarım wetek play cihazım mavi ışık yanmasına rağmen görüntü vermiyor. Bu sayfada bir arkadaşımıza önerdiğiniz iğneli kurtarma yöntemini denedim olmadı. Kutudan çıkan bir ucu stero jack bir ucu port girişi olan kablo nasıl bağlanıyor. Rs232 kablosu mu ? Yabancı forumdaki bağlantıyı deneyeceğim rs32 kablosunu nasıl bağlayacağımı bilemiyorum. Yardeımcı olabilir misiniz
- If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.
Duyuru
Gizle
No announcement yet.
Wetek görüntü yok
Gizle
X
-
massoud Nickli Üyeden Alıntı Mesajı gösterSevgili ustalarım wetek play cihazım mavi ışık yanmasına rağmen görüntü vermiyor. Bu sayfada bir arkadaşımıza önerdiğiniz iğneli kurtarma yöntemini denedim olmadı. Kutudan çıkan bir ucu stero jack bir ucu port girişi olan kablo nasıl bağlanıyor. Rs232 kablosu mu ? Yabancı forumdaki bağlantıyı deneyeceğim rs32 kablosunu nasıl bağlayacağımı bilemiyorum. Yardeımcı olabilir misiniz
saygılarCihazınızda meydana gelebilecek herhangi bir hasar veya veri kaybından sorumlu değilim.
Bütün dosya eklenti ve sunumlar test amaçlıdır.
-
What we need :
1.microSD Card
2.SDcardMaker
3.u-boot.bin
4.Serial debug connection + PuTTY(or some other application)
PREPARE RECOVERY
Start SDcardMaker as Administrator(Right click RunAs),
look Pic.1, after start button, wait for done message , close SDcardMaker, eject microSD Card
Put microSD Card (again) in card reader, copy u-boot.bin on microSD Card, when done - eject microSD Card
RECOVER BOX
Remove Power cable from Wetek Play
Connect serial cable to WeTek Play and PC and start a remote terminal session
Put microSD Card in Wetek Play
Connect Power cable and wait to start booting,
As soon you got the first log lines on terminal session, break boot using CTRL+C keys.
You should now have a prompt “wetek# “, if you fail to get it, please restart box by plugout/in power cable
Type this commands:
-----------------------------------
wetek# mmcinfo
wetek# fatload mmc 0 0x82000000 u-boot.bin
wetek# sf probe 2
wetek# sf erase 0 60000
wetek# sf write 0x82000000 0 60000
wetek# sf erase 0x100000 0x8000
wetek# reset
After reboot, if all was OK yo should boot normally
http://wetektr.com/WeTek/index.php?d...very&s=n&o=asc
http://wetektr.com/WeTek/index.php?d...Tek%20Play.pdf
Yorum yap
-
ozkaradag Nickli Üyeden Alıntı Mesajı gösterHayır bu farklı, cihaz brick olmuş görünüyor.
Bunun için WeTek Play Bölümünde konusu vardı, o işinizi görecektir.
Sevgiler...
saygılarCihazınızda meydana gelebilecek herhangi bir hasar veya veri kaybından sorumlu değilim.
Bütün dosya eklenti ve sunumlar test amaçlıdır.
Yorum yap
-
ozkaradag Nickli Üyeden Alıntı Mesajı gösterBu WP1 için abi.
Brick kelime anlamı tuğla ama buradaki anlamı bloke olmuş cihaz anlamındadır.
Sevgiler...
saygılarCihazınızda meydana gelebilecek herhangi bir hasar veya veri kaybından sorumlu değilim.
Bütün dosya eklenti ve sunumlar test amaçlıdır.
Yorum yap
-
ozkaradag Nickli Üyeden Alıntı Mesajı gösterWhat we need :
1.microSD Card
2.SDcardMaker
3.u-boot.bin
4.Serial debug connection + PuTTY(or some other application)
PREPARE RECOVERY
Start SDcardMaker as Administrator(Right click RunAs),
look Pic.1, after start button, wait for done message , close SDcardMaker, eject microSD Card
Put microSD Card (again) in card reader, copy u-boot.bin on microSD Card, when done - eject microSD Card
RECOVER BOX
Remove Power cable from Wetek Play
Connect serial cable to WeTek Play and PC and start a remote terminal session
Put microSD Card in Wetek Play
Connect Power cable and wait to start booting,
As soon you got the first log lines on terminal session, break boot using CTRL+C keys.
You should now have a prompt “wetek# “, if you fail to get it, please restart box by plugout/in power cable
Type this commands:
-----------------------------------
wetek# mmcinfo
wetek# fatload mmc 0 0x82000000 u-boot.bin
wetek# sf probe 2
wetek# sf erase 0 60000
wetek# sf write 0x82000000 0 60000
wetek# sf erase 0x100000 0x8000
wetek# reset
After reboot, if all was OK yo should boot normally
http://wetektr.com/WeTek/index.php?d...very&s=n&o=asc
http://wetektr.com/WeTek/index.php?d...Tek%20Play.pdf
1. wetekplay2 için serial kabloyu nereden bulabilirim kendimde yapabilirim bağlantı şeması varmı
2. ''u-boot.bin'' weteklpay2 için bu dosyayı nerden bulabilirim.
3. benim cihaz tam kaput oldu.
saygılar
Yorum yap
Yorum yap