• If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Duyuru

Gizle
No announcement yet.

How to for Samsung DSR 9500 VIA CI...

Gizle
X
Gizle
 
  • Sayfa Toplam 1
  • Filtrele
  • Zaman
  • Göster
Hepsini Sil
new posts
Önceki template Sonraki
  • #1

    How to for Samsung DSR 9500 VIA CI...

    If you have problems maybe uploading the new EMU or whatever... All black? Sammy wants SW and from scratch, as it keeps giving you some numbers in the display, like 6-01 changing to 6-03 or so? Well, kill your Sammy at the back and then... Here's a copy of my post from other threads:

    When you switch it on [at the back] press the POWER and LEFT ARROW in the front of the receiver and it should go into Download mode.

    Make sure you have it connected to a PC via a serial cable and your HyperTerminal prepared.

    If it times-out - repeat the procedure until you get it right and in time, too [at the same time keeping your cool!!]!

    Choose the EMU you want to upload. Then Settings list. Then RAM. Then CAID list.

    Enjoy! Hopefully!
    HyperTerminal explanations [thanx to Papagen!!]:

    Uploading Software Into Samsung Using Hyper Terminal

    Start/Program/Accessories/Communications/Hyper Terminal

    Setting the Hyper Terminal

    1. Start Hyper Terminal.
    2. In the field "Name" write for example Samsung 9500, choose an icon and click OK.
    3. In the new opened window, near "Connect using" choose "Direct to COM1, afterwards click OK.

    Port Settings

    1. Bits per second : 115200
    2. Data Bit : 8
    3. Parity : NONE
    4. Stop Bit : 1
    5. Flow Control : Hardware
    Click OK

    Uploading software into Hyper Terminal

    1. Choose TRANSFER
    2. Then choose SEND FILE ....
    3. BROWSE - select from hard drive the desired version of software (e.g. DSR9500_Eurocam_5-1_EMU_vXX.bin)
    4. Choose 1KXmodem for Protocol
    Don't press the button "Send", you will do it subsequently.

    After you have done the procedure described, connect your computer with Samsung using a RS232 connection cable.
    Before you start uploading the new software into Samsung I would advise you to firstly remove all the cams or cards from it (if any are inside).

    The things you have to do are :
    1. Disconnect your Samsung using the switch on the rear.
    2. In the front of Samsung keep pressed the "right arrow" (volume up).
    3. Power up your Samsung on the rear switch and keep constantly pressed "right arrow" (volume up).
    Keep the "arrow" pressed until the "3-01" appears on the display,
    from that moment the computer will show "............................... Loading"
    4. In that moment, in the Hyper Terminal, click the button "Send" (you have about 15 seconds to perform that operation).
    With clicking on "Send" starts the uploading the software into Samsung.
    Don't be hasty! Wait for entire process to terminate.
    Process is terminated when on the Samsung a clock appears.
    Afterwards insert some of the cards with Conax emulation without keys.
    That was it.

    If you have done all properly, there is a desired version of software in you Samsung.
    The easiest way to verify if upload succeeded : Menu/System properties/System information.
    Old versions of the EMU software has the version number 118 and new have 133.
    Enlightenment is man's emergence from self-incurred immaturity = inability to use one's own understanding without the guidance of another => due to lack of resolution and courage to use it without the guidance of another. (Kant)
    Etiketler: Yok
  • #2
    1) Samsung DSR 9500 VIA CI [HW 504, Loader 500 or 501] on Standby

    2) Connect to the PC via straight serial cable

    3) Start Samsung DSR Studio 1.1 Editor by MAHDI

    4) Choose FW Loader TAB

    5) Choose Serial Port

    6) Click on Send FW and then choose which EMU [4.2 at this point - and it's away, racing...]

    7) Wait untill you see the clock on Sammy Display

    8) Start Sammy [on FTA channel, just in case], check it, then put it on Standby

    9) Click on RAM Editor Tab in the Samsung DSR 9500 Studio Editor by MAHDI

    10) Choose Serial Port, then Open File, then click on Write and wait for the clock again

    11) You'll see "Insert smartcard" message, then re-start Sammy

    12) TPS.bin click on Files -> Open Files -> choose the fresh TPS.bin -> when "Ready for Upload" appears -> click on Send -> wait for the clock to appear -> put Sammy to Stand By and switch ON again.

    13) At this point I would [and I am going to]
    Menu -> Channel organising -> Delete all channels and then
    Menu -> Installation -> Manual Scanning and do your own settings list, just so everything is working as it should...

    14) Experiment with various cards, depending on which ones one has...

    15) Sort out the GBox and Card Sharing bits...

    THANKING YOOOOOUUUUUUUUUUUUUUUUUUUUUUU!!!!!!!!!!!!!!!

    MAHDI FOR PRESIDENT!!!
    Enlightenment is man's emergence from self-incurred immaturity = inability to use one's own understanding without the guidance of another => due to lack of resolution and courage to use it without the guidance of another. (Kant)

    Yorum yap

    • #3
      In Gold Emu 4.x you have this as an option:

      Press 0 and then Menu and you get into the main Emulator Menu.

      At the bottom you have Key Editor Menu -> choose a coding system 0 -> Ident -> key you wanna change by using this scheme:

      0 = 0 Button

      1 = 1 Button

      2 = 2 Button

      3 = 3 Button

      4 = 4 Button

      5 = 5 Button

      6 = 6 Button

      7 = 7 Button

      8 = 8 Button

      9 = 9 Button

      A = PG+ Button

      B = PG- Button

      C = GREEN Button

      D = YELLOW Button

      E = BLUE Button

      F = RED Button

      Del = LAST Button
      Enlightenment is man's emergence from self-incurred immaturity = inability to use one's own understanding without the guidance of another => due to lack of resolution and courage to use it without the guidance of another. (Kant)

      Yorum yap

      • #4
        By DSR 9500: Hard-reset-method (hard reset, hard-reset-procedure).

        Put Sammy FIRST ON FTA channel (Free-To-Air = not encrypted)
        Put Sammy in standby (front-switch)
        Wait a moment for Sammy to act.
        Now switch of, at the back-side en 2 seconds later
        Swich on at the backside.

        Might be needed to press ON-switch at front twice, but now Sammy had a hard reset.
        Problem of freezes or serial mis-communication should be solved.
        Enlightenment is man's emergence from self-incurred immaturity = inability to use one's own understanding without the guidance of another => due to lack of resolution and courage to use it without the guidance of another. (Kant)

        Yorum yap

        • #5
          Btw, you don't need the old empty Conax card with Gold Emu 4.2.

          Your Emulator needs to be ON [press 0 and then Menu quickly].

          If you have problems, just repeat the whole procedure with killing it at the back, after Resetting it to Factory Default via remote. Restart the PC, too.

          Use HyperTerminal as described above if DSR Studio isn't working. Step by step. Exactly as described!

          Good luck!
          Enlightenment is man's emergence from self-incurred immaturity = inability to use one's own understanding without the guidance of another => due to lack of resolution and courage to use it without the guidance of another. (Kant)

          Yorum yap

          • #6
            How To Flash Your Sammy And Get The Au To Work!!!

            [Remember: switch your Sammy off at the back BEFORE and AFTER you program the EMU in! Do not hurry, do not cut corners, if you want it all to work properly!]

            After Sammy has cooled down a bit [say 5 - 10 minutes] switch it on at the back and keep it on Standby.

            Now start the STUDIO 1.2 [or 1.3] by MAHDI and go to DSR FW Loader and Send FW, then choose the Emu and Open -> to put the EMU in. Wait for the clock on Sammy display, do not rush!

            When you start Sammy via a remote go to RESET EMU [again: via a remote] by pressing 0 + Menu quickly in succession, then go down to RESET TO EMU DEFAULTS and press the OK button on your remote.

            (After it resets you can go back to EMU MENU to make sure you have the following configuration:

            EMU - ON
            EMM - ON
            CAID Mode - AUTO
            CS Mode - SSSP [if you need that one or HSIC if you're sharing via the Hummy CS SW]
            EMU Active Mode - NO CARD [One doesn't need the Conax Card nowadays!])

            Put Sammy to Standby and then kill at the back for a few minutes.

            Restart your Sammy at the back, then leave it on Standby.

            Now put the RAM in [Cruiser's are excellent!], if you need to, then start Sammy via remote.

            ==================================================

            Now the AU function for D+, Premiere and TPS            :

            Go to a channel in D+, for instance [I just did it on Taquila 7], then do the following...

            By the way, sometimes you will need to scan some transponders, as Sammy likes to "see all the data" for himself - only then can you see some transponders/channels - if you put in somebody else's settings, like Cuorino's good work!

            Go to EMU Menu, where you should have:

            EMU - ON
            EMM - ON
            CAID Mode - AUTO
            CS Mode - SSSP [if you need that one or HSIC if you're sharing via the Hummy CS SW]
            EMU Active Mode - NO CARD [One doesn't need the Conax Card nowadays!]

            Now do the EMU RESET, as described above, by pressing 0 + Menu quickly in succession, then go to RESET TO EMU DEFAULTS and OK.

            Wait a little bit - it's fast to AU on all 3 providers!

            Once you have the pretty colours go to the next of the 3 big publicly hacked providers [a channel of your choice]. Put your Sammy to Standby, then re-start it. Repeat the EMU Menu Reset to AU.

            It should AU, provided you scanned the transponder on which you wanna AU.

            Just flashed the receiver with 5.9 and tested:

            TPS AU works fast! AU on FRANCE 4 [or any channel on that transponder]. Works great, no problems with flickering and freezing!

            D+, too!

            Premiere also!

            Showtime and Pehla tested by anyone? The reports are that, at the moment, they are not working AU...

            Enjoy [you lazy sods, who can't be bothered to read a bit, too...:mefta:]!!

            D+ and Premiere are not AU at the moment, Cabo is gone, D+ soon, too. DigiTV is working but not AU, I think... Enjoy anyway...
            Enlightenment is man's emergence from self-incurred immaturity = inability to use one's own understanding without the guidance of another => due to lack of resolution and courage to use it without the guidance of another. (Kant)

            Yorum yap

            • #7
              In addition:

              do NOT reset the EMU every time you want a provider to AU!!!

              Do it just once, after the installation!

              Then put the RAM.bin in...

              Every time you reset it it seems to wipe the keys off and one has to wait for each provider to AU, then...

              Instead, as I said, reset it once, after the installation and then just leave it on a channel and wait for the AU to happen!


              There, my good deed for the day is done...
              Enlightenment is man's emergence from self-incurred immaturity = inability to use one's own understanding without the guidance of another => due to lack of resolution and courage to use it without the guidance of another. (Kant)

              Yorum yap

              • #8
                HOW TO PROGRAMME YOUR SAMMY

                Switch your Sammy off at the back BEFORE you program the EMU in!

                After Sammy has cooled down a bit [say 2-3 minutes] switch it on at the back and keep it on Standby.

                Now start the STUDIO 1.2 [or 1.3] by Maestro MAHDI and go to DSR FW Loader and Send FW, then choose the Emu [now 6.3] and Open -> to put the EMU in. Wait for the clock on Sammy display, do not rush!

                HOW TO GET YOUR AU TO WORK

                Using your remote, start your Sammy from Standby and do a RESET OF EMU by pressing 0 + Menu on your remote, quickly in succession! Then go down to RESET TO EMU DEFAULTS and press the OK button on your remote.

                Sammy will switch itself off now. Use your remote to start it from Standby.

                Go to the EMU MENU [by pressing 0 + Menu in quick succession] and you will see the following configuration:

                EMU - ON
                EMM - ON
                CAID Mode - AUTO
                Sharing Mode - HSIC - that's for Humax CS [change to the protocol you need, when using CS; SSSP DSR for GBox and DSR for Sammy original]
                DCW Delay - experiment to see which setting here gets you a better result
                RS232 Delay - as above, see which setting here gets you a better result

                PREMIERE, TPS and SRG SWISS

                Here I couldn't get the picture, that is to say the AU on Premiere to work for me, so I changed the channel and it still didn't work. So, I put the receiver to Standby via Remote [do not kill it at the back - no need for that any more!], then I switched it back on immediately - and the picture came very quickly!!! Maybe I just didn't wait for long enough? Anyway, the AU is working nicely!

                After that go to TPS/Canal+ France [France 4, or any channel on that transponder] and leave it there - the AU was very fast!

                Then, go to SRG Swiss and wait a bit for AU here. A minute or two...

                NOW PUT THE RAM.bin IN

                Now put your Sammy to Standby, and then put the RAM.bin file [with all the other keys] in [Cruiser or Oys], then start your Sammy via remote. All working fine, including DigiTV!

                GREAT JOB, MAHDI!!!
                Enlightenment is man's emergence from self-incurred immaturity = inability to use one's own understanding without the guidance of another => due to lack of resolution and courage to use it without the guidance of another. (Kant)

                Yorum yap

                Önceki template Sonraki
                Hazırlanıyor...
                X